If the video drivers don't help try upping the voltage on your Ram.....that BSOD messages reminds me of a ram error from overclocking......

Cooler Master HAF 932
Gigabyte GA-EP45-UD3P Rev. 1.6
Core 2 Quad Q9550 2.83Ghz E0 3.40Ghz OC'ed
w/ Cooler Master V-8
XFX Radeon HD 4870 1GB DDR5
4x2GB G. Skill DDR2 1066
Corsair 750W PSU Single Rail
(2) WD 640GB Caviar Black HDD
(1) WD 500GB Caviar Black HDD
(1) Seagate 500GB
Samsung 22X DVD Burner SATA
Windows 7 64-bit

and I'd probably agree if the OP had not OC'ed his system......Technet doesn't usually deal with that end of the spectrum. In this case they may well be right. I agree you should update to the latest Vid driver first. BUT it may be unstable ram

I've seen the same BSOD a number of times and "for me" it related back to memory settings. Not sure whether it was timings or voltages but once I got the memory stable I stopped getting the dreaded BSOD

none at all.....just go gentle. The HAF932 is about the size of a 1-bdr apartment.....if my wife ever throws me out I'll put the wheels on and move in.

lets see......this is my MOST Stable setup.....at 3.4 Ghz..........Pushing the CPU over 3.44Ghz and it changes everything

not only that but heat becomes more of an issue. right now I rarely see a temp in the 40C+ and never 50C+ evn with the radeon frying eggs

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [8x]
Fine CPU Clock Ratio ----------------- : [0.5]
CPU Frequency ---------------------: 3.40 mhz [400x8.5]

Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [400]
PCI Express Frequency (Mhz) ---------- : [100]

C.I.A.2 ------------------------------ : [Disabled]

Advanced Clock Control
CPU Clock Drive ---------------------- : [800]
PCI Express Clock Drive -------------- : [900]
CPU Clock Skew (ps) ------------------ : [  0]
MCH Clock Skew (ps) ------------------ : [  0]

DRAM Performance Control
Performance Enhance ------------------ : [Standard] I can set to turbo....more of a prefernce thing..
Extreme Memory Profile --- (X.M.P.) -- : [Disabled]
(G)MCH Frequency Latch --------------- : [400]
System Memory Multiplier ------------- : [2.0D]       you can try 2.66D but again....
Memory Frequency (Mhz) --------------- : [1066 800]   I had to go 1.4 on MCH Core...not good
DRAM Timing Selectable --------------- : [Manual]

Standard Timing Control
CAS Latency Time --------------------- : [5] started at 5-7-7-20...ended up with stock values after tweaking
tRCD --------------------------------- : [5]
tRP ---------------------------------- : [5]
tRAS --------------------------------- : [15]

Advanced Timing Control
tRRD --------------------------------- : [4]
tWTR --------------------------------- : [4]
tWR ---------------------------------- : [8]
tRFC --------------------------------- : [68] <---pain in the butt.....started at 80....can't go lower
tRTP --------------------------------- : [4]
Command Rate (CMD) ------------------- : [2]

Driving Strength Profiles
Driving Strength --------------------- : [Auto]


Channel A
Static tRead Value ------------------- : [8] managed to boot and run w/7 but question stability
tRD Phase0 Adjustment ---------------- : [Auto]
tRD Phase1 Adjustment ---------------- : [Auto]
tRD Phase2 Adjustment ---------------- : [Auto]
tRD Phase3 Adjustment ---------------- : [Auto]
Trd2rd(Different Rank) --------------- : [Auto]
Twr2wr(Different Rank) --------------- : [Auto]
Twr2rd(Different Rank) --------------- : [Auto]
Trd2wr(Same/Diff Rank) --------------- : [Auto]
Dimm1 Clock Skew Control ------------- : [Auto]
Dimm2 Clock Skew Control ------------- : [Auto]
DDR Write Training --------------------: [Auto]

Channel B
Static tRead Value ------------------- : [8]
tRD Phase0 Adjustment ---------------- : [Auto]
tRD Phase1 Adjustment ---------------- : [Auto]
tRD Phase2 Adjustment ---------------- : [Auto]
tRD Phase3 Adjustment ---------------- : [Auto]
Trd2rd(Different Rank) --------------- : [Auto]
Twr2wr(Different Rank) --------------- : [Auto]
Twr2rd(Different Rank) --------------- : [Auto]
Trd2wr(Same/Diff Rank) --------------- : [Auto]
Dimm1 Clock Skew Control ------------- : [Auto]
Dimm2 Clock Skew Control ------------- : [Auto]
DDR Write Training --------------------: [Auto]

Motherboard Voltage Control
CPU
Load-Line Calibration ---------------- : [Enabled]
CPU Vcore --------------- 1.2375 ----- : [1.24375]
CPU Termination --------- 1.2000 ----- : [1.2000]
CPU PLL ----------------- 1.5000 ----- : [1.5000]
CPU Reference ----------- 0.7600 ----- : [Auto]

MCH/ICH
MCH Core ---------------- 1.100 ------ : [1.300]
MCH Reference ----------- 0.760 ------ : [Auto]
MCH/DRAM Ref ------------ 0.900 ------ : [Auto]
ICH I/O ----------------- 1.500 ------ : [1.570]
ICH Core ---------------- 1.100 ------ : [1.100]

DRAM
DRAM Voltage ------------ 1.800 ------ : [2.100]
DRAM Termination -------- 0.900 ------ : [Auto]
Channel A Reference ----- 0.900 ------ : [Auto]
Channel B Reference ----- 0.900 ------ : [Auto]

Advanced Settings
Limit CPUID Max. to 3 ---------------- : [Disabled]
No-Execute Memory Protect ------------ : [Enabled]
CPU Enhanced Halt (C1E) -------------- : [Disabled]
C2/C2E State Support ----------------- : [Disabled]
x C4/C4E State Support --------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ---------- : [Enabled]
CPU EIST Function -------------------- : [Disabled]
Virtualization Technology ------------ : [Disabled]

Integrated Peripherals
Legacy USB Storage Detect ------------ : [Disabled]

your welcome...remember to "Load Optimized Defaults" before you tweak....